基本信息
| 标准名称： | 危险品 易燃黏性液体黏度试验方法 |
| 英文名称： | Dangerous goods - Viscosity test for of flammable viscous liquids |
| 中标分类： |
综合 >>
标志、包装、运输、贮存 >>
标志、包装、运输、贮存综合 |
| ICS分类： |
环保、保健与安全 >>
危险品防护
|
| 发布部门： | 中华人民共和国国家质量监督检验检疫总局 国家标准化管理委员会 |
| 发布日期： | 2008-04-01 |
| 实施日期： | 2008-09-01 |
| 首发日期： | 2008-04-01 |
| 作废日期： | |
| 主管部门： | 国家标准化管理委员会 |
| 提出单位： | 全国危险化学品管理标准化技术委员会（SAC/TC 251） |
| 归口单位： | 全国危险化学品管理标准化技术委员会 |
| 起草单位： | 江苏检验检疫局、中化化工标准化研究所、北京出入境检验检疫局 |
| 起草人： | 刘君峰、张君玺、王晓兵、徐思桥、刘国传、唐树田、唐建明 |
| 出版社： | 中国标准出版社 |
| 出版日期： | 2008-06-01 |
| 页数： | 4页 |
| 计划单号： | 20068248-T-469 |
| 书号： | 155066·1-31492 |
适用范围
本标准为首次制定。本标准规定了黏性液体的黏度试验的仪器与设备、操作步骤和结果的表示。本标准适用于油漆、搪瓷、清漆、胶黏剂和抛光剂等闪点低于23℃的黏性液体。 本标准对应于联合国《关于危险货物运输的建议书：试验和标准手册》（第四修订版），与其一致性程度为非等效。本标准有关技术内容与上述手册完全一致，在标准文本格式上按ＧＢ／Ｔ１．１—２０００做了编辑性修改。
前言
没有内容
目录
没有内容
引用标准
下列文件中的条款通过本标准的引用而成为本标准的条款。凡是注日期的引用文件，其随后所有的修改单（不包括勘误的内容）或修订版均不适用于本标准，然而，鼓励根据本标准达成协议的各方研究是否可使用这些文件的最新版本。凡是不注日期的引用文件，其最新版本适用于本标准。
GB19458 危险货物危险特性检验安全规范 通则
GB19521.2 易燃液体危险货物危险特性检验安全规范
ISO2431 涂料和清漆 用流量杯测定流出时间
联合国《关于危险货物运输的建议书：试验和标准手册》（第四修订版）
所属分类： 综合 标志 包装 运输 贮存 标志 包装 运输 贮存综合 环保 保健与安全 危险品防护
Product Code:SAE J1978
Title:OBD II Scan Tool -- Equivalent to ISO/DIS 15031-4:December 14, 2001
Issuing Committee:Vehicle E E System Diagnostic Standards Committee
Scope: This SAE Recommended Practice supersedes SAE J1978 FEB1998, and is technically equivalent to ISO/DIS 15031-4:December 14, 2001. This document is intended to satisfy the requirements of an OBD scan tool as required by U.S. On-Board Diagnostic (OBD) regulations. The document specifies: a. A means of establishing communications between an OBD-equipped vehicle and external test equipment, b. A set of diagnostic services to be provided by the external test equipment in order to exercise the services defined in SAE J1979, c. Conformance criteria for the external test equipment. Differences from ISO Document The ISO 15031-4 document is intended to satisfy the requirements of OBD requirements in countries other than the U.S., and includes functionality not required or not allowed in the U.S. Notable exceptions are: a. Proposed U.S. OBD regulations will allow ISO 15765-4 as an allowable OBD serial data link at 500 kbps only. Only those provisions of ISO 15765-4 that pertain to 500 kbps are required to be supported by an SAE J1978 diagnostic scan tool. b. Proposed U.S. OBD regulations will not allow greater than 20 V at the SAE J1962 connector. Only the Type A connector as defined in SAE J1962 needs to be supported by an SAE J1978 diagnostic scan tool. Differences between the documents are highlighted in the technical requirements sections of this document. Deleted text is highlighted with struck through and new text is highlighted with bold italic. NOTE - To maintain equivalency of the documents, a comma is used as a decimal marker for numeric values in this document.
Rationale: This SAE Recommended Practice supersedes SAE J1978 FEB1998, and is technically equivalent to ISO/DIS 15031-4:December 14, 2001. This document is intended to satisfy the requirements of an OBD scan tool as required by U.S. On-Board Diagnostic (OBD) regulations. The document specifies: a. A means of establishing communications between an OBD-equipped vehicle and external test equipment, b. A set of diagnostic services to be provided by the external test equipment in order to exercise the services defined in SAE J1979, c. Conformance criteria for the external test equipment. Differences from ISO Document The ISO 15031-4 document is intended to satisfy the requirements of OBD requirements in countries other than the U.S., and includes functionality not required or not allowed in the U.S. Notable exceptions are: a. Proposed U.S. OBD regulations will allow ISO 15765-4 as an allowable OBD serial data link at 500 kbps only. Only those provisions of ISO 15765-4 that pertain to 500 kbps are required to be supported by an SAE J1978 diagnostic scan tool. b. Proposed U.S. OBD regulations will not allow greater than 20 V at the SAE J1962 connector. Only the Type A connector as defined in SAE J1962 needs to be supported by an SAE J1978 diagnostic scan tool. Differences between the documents are highlighted in the technical requirements sections of this document. Deleted text is highlighted with struck through and new text is highlighted with bold italic. NOTE - To maintain equivalency of the documents, a comma is used as a decimal marker for numeric values in this document.